ioapic problem

["ºñ¿¡½ºµð" <bsdman@xxxxxxxxx>]

안녕하세요.

인텔 SE7500CW2 보드에 FreeBSD4.7를 설치해서 FreeBSD4.7p4로
업그레이드 하던중 IOAPIC에서 에러가 발생하여 도움을 요청합니다.
SMP 옵션을 켜지 않을때는 아무런 이상이 없지만, SMP를 켜놓고 컴파일 할경우
에러가 발생합니다.

다음은 dmesg 내용입니다.
panic y/n? [y]
이 부분에서 멈춰있고, n를 누르면 진행이 되지만, 두번째 CPU인 CPU #1이 붙지 
않은 상태입니다.

CMOS의 hyper threading기능과 관련이 있을수 있다고 합니다만, 이 옵션은 disabled 시켜놓고 진행했습니다.
참고로 시스템 사양은
Intel XEON 2.4G Dual
DDR 512M *2
Seagate 18.2G SCSI HDD
입니다.


Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 4.7-RELEASE-p4 #0: Tue Feb 18 09:58:46 KST 2003
    root@xxxxxxxxxx:/usr/obj/usr/src/sys/test
Timecounter "i8254"  frequency 1193182 Hz
CPU: Pentium 4 (2392.25-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf27  Stepping = 7
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,<b28>,ACC,<b31>>
real memory  = 1073217536 (1048064K bytes)
config> di psm0
config> di sio1
config> di sio0
config> di ppc0
config> di sn0
config> di lnc0
config> di ie0
config> di fe0
config> di ed0
config> di cs0
config> di bt0
config> di adv0
config> q
avail memory = 1039261696 (1014904K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
Programming 24 pins in IOAPIC #1
Programming 24 pins in IOAPIC #2
AP #1 (PHY# 6) failed!
panic y/n? [y] FreeBSD/SMP: Multiprocessor motherboard
 cpu0 (BSP): apic id:  0, version: 0x00050014, at 0xfee00000
 cpu1 (AP):  apic id:  6, version: 0x00000000, at 0xfee00000
 io0 (APIC): apic id:  2, version: 0x00178020, at 0xfec00000
 io1 (APIC): apic id:  3, version: 0x00178020, at 0xfec80000
 io2 (APIC): apic id:  4, version: 0x00178020, at 0xfec80400
Preloaded elf kernel "kernel" at 0xc0521000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc052109c.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 17 entries at 0xc00fdeb0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
IOAPIC #0 intpin 16 -> irq 2
IOAPIC #0 intpin 19 -> irq 3
IOAPIC #0 intpin 17 -> irq 5
pci0: <PCI bus> on pcib0
pci0: <unknown card> (vendor=0x8086, dev=0x2541) at 0.1
pcib1: <PCI to PCI bridge (vendor=8086 device=2543)> at device 2.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <unknown card> (vendor=0x8086, dev=0x1461) at 28.0
pcib2: <PCI to PCI bridge (vendor=8086 device=1460)> at device 29.0 on pci1
pci2: <PCI bus> on pcib2
pci1: <unknown card> (vendor=0x8086, dev=0x1461) at 30.0
pcib3: <PCI to PCI bridge (vendor=8086 device=1460)> at device 31.0 on pci1
IOAPIC #2 intpin 0 -> irq 10
pci3: <PCI bus> on pcib3
sym0: <1010-66> port 0x8000-0x80ff mem 0xfc200000-0xfc201fff,0xfc202000-0xfc2023ff irq 10 at device 1.0 on pci3
sym0: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: handling phase mismatch from SCRIPTS.
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x7000-0x701f irq 2 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0x7020-0x703f irq 3 at device 29.1 on pci0
usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
pcib4: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on pci0
IOAPIC #0 intpin 21 -> irq 11
IOAPIC #0 intpin 20 -> irq 16
IOAPIC #0 intpin 23 -> irq 17
pci4: <PCI bus> on pcib4
pci4: <ATI Mach64-GR graphics accelerator> at 3.0 irq 11
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x9400-0x943f mem 0xfc300000-0xfc31ffff,0xfc341000-0xfc341fff irq 16 at device 4.0 on pci4
fxp0: Ethernet address 00:02:b3:af:75:d8
inphy0: <i82555 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1: <Intel Pro 10/100B/100+ Ethernet> port 0x9440-0x947f mem 0xfc320000-0xfc33ffff,0xfc342000-0xfc342fff irq 17 at device 5.0 on pci4
fxp1: Ethernet address 00:02:b3:af:76:9d
inphy1: <i82555 10/100 media interface> on miibus1
inphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI to ISA bridge (vendor=8086 device=2480)> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 ATA100 controller> port 0x7040-0x704f,0-0x3,0-0x7,0-0x3,0-0x7 irq 0 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <unknown card> (vendor=0x8086, dev=0x2483) at 31.3 irq 5
orm0:  at iomem 0xc0000-0xc7fff,0xc8000-0xcbfff,0xe3800-0xe3fff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
acd0: CDROM <LG CD-ROM CRN-8245B> at ata1-master PIO4
Waiting 15 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
Mounting root from ufs:/dev/da0s1a
da0 at sym0 bus 0 target 0 lun 0
da0: <SEAGATE ST318406LC 010A> Fixed Direct Access SCSI-3 device 
da0: 160.000MB/s transfers (80.000MHz, offset 62, 16bit), Tagged Queueing Enabled
da0: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C)

 

지식까지 찾아주는 검색 - 네이버 못찾을 땐! 네이버에 물어보세요!

Clean mail, 네이버 메일 깨끗한 메일환경! 네이버와 함께 하세요.